The bolt handle, rear of the bolt body, safety lever (faded), top rear of the bolt body (faded) and barrel are marked with the serial number '8658'. The magazine plate, nose cap and barrel band and are marked '8958'.
On the end of the barrel it has stamped K98 Yugo 8mm on right side on top it has CAI ST A VT, (mine isn't ALB after ST like I've seen only A.)all the serial numbers match V85xx (last two Xs. Mauser Oberndorf Data for K98k Hi guys happy to join you. I bought in 2004 a byf44 K98k with serial number 15947g with high turrets and scope. There are some marks on it that i really don't understand, so i hope that you can help me to decifrate. By the way I tried to attach some pictures of my mauser but those are too big for the sistem.
Sold for: $1,230.03
Make: dou (Waffen Werke, Brunn, Bystrica) Waffen Werke Bystrica is located in Slovakia and is the sister factory to Waffen Werke Brunn in Czechoslovakia.
Model: K98
K98 Mauser Serial Numbers Lookup
Serial Number: 8658
Year of Manufacture: 1944 Drivers realtek audio win 10 64 bits.
Caliber: 8mm Mauser (7.92X57mm)
Action Type: Bolt Action with Internal Magazine
Markings: There is no visible import mark. The top of the receiver is marked with a Nazi Waffenamt Eagle over 'WaA A80', the factory code 'dou' and the year '44'. The left side of the receiver is marked 'Mod. 98'. The bolt handle, rear of the bolt body, safety lever (faded), top rear of the bolt body (faded) and barrel are marked with the serial number '8658'. The magazine plate, nose cap and barrel band and are marked '8958'. The barrel is also marked with a Nazi Eagle over Swastika, 'M', 'E', a triangle, 'dou' and with two faded inspection stamps Eagle over '180'. The underside of the bolt handle is marked with an inspection stamp that is faded. The tang in front of the magazine is marked 'byf' and with an inspection stamp. The sling well is marked 'B' and 'H'.
Barrel Length: Approximately 24'
Sights / Optics: The front sight is a hooded, inverted 'V' post. The rear sight is a sliding 'V' notched sight elevator marked from '1 – 20'.
Stock Configuration & Condition: The two piece hardwood stock has a pistol grip, sling well, sling pass through, metal nose cap, barrel band with sling loop, through bolt, domed washer and metal butt plate. The stock has various small scrapes and scratches. There are compression marks under the stock. There is a thin hairline crack in front of the magazine. The LOP measures 13' from the front of the trigger to the back of the butt plate. The stock rates in about Very Good overall condition.
Type of Finish: Blue
Finish Originality: Original, except the bolt body was refinished.
Bore Condition: The bore is bright and the rifling is deep. There is light erosion near the muzzle.
Overall Condition: This rifle retains about 85% of its metal finish. The balance of the finish shows the beginning of a brown patina. The front of the barrel, front sight band and hood show light scratches and fading. There are several small marks on the receiver. The bolt release lever and bolt body do not match the finish of the rifle. The stock metal shows wear and the butt plate also shows some corrosion. The screw heads are intact. The markings are deep. Overall, this rifle rates in about Very Good condition.
German 98 Mauser Serial Numbers
Mechanics: The action functions correctly. We have not fired this rifle.
Box, Paperwork& Accessories: This rifle comes with a leather sling that is marked 'MADE IN / GEMANY' on the inside. It show light wear and is in Very Good to Fine condition.
Our Assessment: This German Mauser K98 was made at the Waffen Werke Bystrica factory which was located in Slovakia during WWII. The rifle has clear Nazi marks and does not have Russian Capture marks. This rifle is ideal for the Military Surplus or WWII collector. Nazi marked k98 rifles are nowhere near as common as the used to be back in the 'good old days', so If you don't have one, get one.
| Model Designation: | Karbiner 98 Kurz |
| Caliber: | 7.92mm (7.92X57) |
| Overall Length: | 1,110mm (43.7') |
| Weight: | Solid stock; 3.8kg (8.38lbs.) Laminated stock: 4kg. |
| Magazine: | 5 round, fixed box |
| Front sight: | Inverted 'V' notch (later models had a sight hood cover) |
| Rear sight: | 'V' notch adjustable up to 2,000 meters |
| Rifling: | 4 grooves, right hand twist, one turn every 240mm |
| Safety: | 3-way safety lever on rear of bolt. Left to fire, right to safe, center to load. |
| Markings: | With few exceptions, every K98 was stamped with manufacturers' code and date on top of receiver. |
Caliber: 8mm Mauser (7.92X57mm)
Action Type: Bolt Action with Internal Magazine
Markings: There is no visible import mark. The top of the receiver is marked with a Nazi Waffenamt Eagle over 'WaA A80', the factory code 'dou' and the year '44'. The left side of the receiver is marked 'Mod. 98'. The bolt handle, rear of the bolt body, safety lever (faded), top rear of the bolt body (faded) and barrel are marked with the serial number '8658'. The magazine plate, nose cap and barrel band and are marked '8958'. The barrel is also marked with a Nazi Eagle over Swastika, 'M', 'E', a triangle, 'dou' and with two faded inspection stamps Eagle over '180'. The underside of the bolt handle is marked with an inspection stamp that is faded. The tang in front of the magazine is marked 'byf' and with an inspection stamp. The sling well is marked 'B' and 'H'.
Barrel Length: Approximately 24'
Sights / Optics: The front sight is a hooded, inverted 'V' post. The rear sight is a sliding 'V' notched sight elevator marked from '1 – 20'.
Stock Configuration & Condition: The two piece hardwood stock has a pistol grip, sling well, sling pass through, metal nose cap, barrel band with sling loop, through bolt, domed washer and metal butt plate. The stock has various small scrapes and scratches. There are compression marks under the stock. There is a thin hairline crack in front of the magazine. The LOP measures 13' from the front of the trigger to the back of the butt plate. The stock rates in about Very Good overall condition.
Type of Finish: Blue
Finish Originality: Original, except the bolt body was refinished.
Bore Condition: The bore is bright and the rifling is deep. There is light erosion near the muzzle.
Overall Condition: This rifle retains about 85% of its metal finish. The balance of the finish shows the beginning of a brown patina. The front of the barrel, front sight band and hood show light scratches and fading. There are several small marks on the receiver. The bolt release lever and bolt body do not match the finish of the rifle. The stock metal shows wear and the butt plate also shows some corrosion. The screw heads are intact. The markings are deep. Overall, this rifle rates in about Very Good condition.
German 98 Mauser Serial Numbers
Mechanics: The action functions correctly. We have not fired this rifle.
Box, Paperwork& Accessories: This rifle comes with a leather sling that is marked 'MADE IN / GEMANY' on the inside. It show light wear and is in Very Good to Fine condition.
Our Assessment: This German Mauser K98 was made at the Waffen Werke Bystrica factory which was located in Slovakia during WWII. The rifle has clear Nazi marks and does not have Russian Capture marks. This rifle is ideal for the Military Surplus or WWII collector. Nazi marked k98 rifles are nowhere near as common as the used to be back in the 'good old days', so If you don't have one, get one.
| Model Designation: | Karbiner 98 Kurz |
| Caliber: | 7.92mm (7.92X57) |
| Overall Length: | 1,110mm (43.7') |
| Weight: | Solid stock; 3.8kg (8.38lbs.) Laminated stock: 4kg. |
| Magazine: | 5 round, fixed box |
| Front sight: | Inverted 'V' notch (later models had a sight hood cover) |
| Rear sight: | 'V' notch adjustable up to 2,000 meters |
| Rifling: | 4 grooves, right hand twist, one turn every 240mm |
| Safety: | 3-way safety lever on rear of bolt. Left to fire, right to safe, center to load. |
| Markings: | With few exceptions, every K98 was stamped with manufacturers' code and date on top of receiver. |
In June 1934, the German army adopted the Mauser Karbiner 98 kurz as the standard service rifle of the German army. It remained in service until the end of the war in May 1945. Eleven years in production produced over 14 million K98s, and out of the 14 million produced, there are over 100 combinations of maker codes and production years. All of this combined with the fact that the Mauser K98 is one of the best bolt actions designs of all time, makes the K98k one of the most collectable rifles of WWII, and perhaps of all time.
Dates, Makers, and Codes :
In 1934 only two manufacturers where assigned to produce the K98k. These were the Mauser plant at Obendorf, and the firm of J.P. Sauer & Sohn at Suhl. Mauser, Obendorf was the only manufacturer to produce the K98 from 1934-1945. Each year later, other makers were added to produce the K98k, while some makers where dropped due to production demands or interests in producing other weapons, such as machine guns, machine pistols, or other small arms that were needed. By 1943 there were at least 7 factories that were producers of the rifle. Each makers code, dates, and proof markings for each year are listed below.
| 1934 |
|
| 1935 |
|
| 1936 |
|
| 1937 |
|
| 1938 |
|
| 1939 |
|
| 1940 |
|
| 1941 |
|
| 1942 |
|
| 1943 |
|
| 1944 |
|
| 1945 |
*- Later (higher) serial numbers were issued as Kriegsmodells. |
K98 Variations-
During the war several changes and/or alterations were made to the K98. Most of these changes were simply design alterations that were made to simplify or increase production of the rifle. Some of these were totally different model of the K98, including the G33/40. The G33/40 was basically a shortened version of the K98. How to make a footnote two columns in microsoft word for mac. The G33/40 was only in production for 3 years, from 1940-1942. It was produced by Waffen Werke Brunn, Brunn. It fired the exact same 7.92mm round, and had the same Mauser 98 action. However, that is where the similarities end. The G33/40 had several different parts that were not matching with the K98. These included: the bolt, stock, cleaning rod, sight hood cover, upper hand guard, barrel bands, sling, and even the bayonet. Below is an example of the G33/40, that was made in 1941, and bears the maker's code 'dot 1941.' Note also in the pictures below the differences between the standard K98 and the G33/40.
Another example of the changes made to the K98 late in the war is the introduction of the Kriegsmodell K98. The Kriegsmodell K98 is basically the most simplified version of the K98. Several design changes were made to produce the Kriegsmodell. Several items were completely eliminated, such as: bayonet lug, cleaning rod, bolt disassembly disk, bolt guide, barrel band spring, and even the locking screws for the floor plate. Kriegsmodell K98s are usually late 1944 or 1945 production. They will usually have very rough machined parts, and stocks will be rough and usually unfinished. Below are pictures of a Kriegsmodell K98, that was made by Mauser, Obendorf in 1945, and is marked 'byf 45.' Note also in the pictures below the differences between the standard K98, and the Kriegsmodell K98.
All pictures below submitted by Matt Weber unless otherwise stated
Click on images to enlarge
| K98 made by Mauser, Obendorf in 1945, and labeled 'byf 45'. Notice the phosphated finish to this piece, and also notice that the model designation 'Mod. 98' has been moved from the side of the receiver to the top of the receiver. |
| K98 made by Waffen Werke, Brunn, Brunn in 1944, and is marked 'dot 1944'. Note that this late war K98 is marked with the full year 1944, and not just the partial year '44' or simply '4'. Also notice the rough machine markings on this late war piece. |
| K98 made by Waffen Werke, Brunn, Bystrica in 1943, and is marked 'dou 43'. Typical mid-war production and finish on this piece |
| G33/40 made by Waffen Werke, Brunn, Brunn, and is marked 'dot 1941'. Note the caliber markings on top of the receiver, 7,88. Also notice that the upper hand guard wood wraps around behind the rear sight. |
| Comparison of the standard K98 bolt (right), and the Kriegsmodell K98 bolt (left). Notice the bolt on the right has typical milled out, oval shaped cooling holes, while the bolt on the left has round, drilled out cooling holes. |
| This picture shows us 2 K98 bolts. Notice that the bolt on the left is missing the bolt guide. That's because this bolt is a Kriegsmodell K98 bolt. Notice also that it is parkerized. The one on the right is a standard K98 bolt, and is blued. |
| Two floor plates for the K98. The one on the right is a milled floorplate. This type can be found on pre-war, and early war time K98 models. The left one is a stamped floor plate, and is found on late war K98s. Notice also on this one that it is also missing the locking screws. That is because this floor plate is for a K98 Kriegsmodell. |
| Two K98 trigger guards. The one on the right is a milled trigger guard. Again these are found on pre-war and early war K98s. The one on the left is a stamped trigger guard, and is found on late war K98s. Notice again that this stamped trigger guard is missing the locking screws, which means that this trigger guard is for a Kriegsmodell K98. |
| Front barrel band. This is a mid-war production barrel band. It is milled type, but not formed like the 'H' types. Serial number are marked on these, but late war stamped barrel bands usually won't have serial numbers on them. This is a 1943 date K98. |
| The test firing proof will be located on the aft of the bolt handle. As shown here. |
| Serial numbers on the k98 stocks are usually located under the stock, half way between the hand grip, and the buttplate. As shown here. |
| Bolt of the K98 shows us 3 serial number locations: top of bolt, safety lever, and bolt handle. |
| Serial numbers as found on the rear sight leaf, and sight adjustment. Note that very late war K98s might not have any serial numbers marked on these parts. All early war or pre-war K98s should have serial numbers on these though! This K98 is a 1943 date. |
| Serial numbers for the reciever and barrel on a K98. Note aslo the acceptance proof markings. |
| Serial numbers also found on rear sight base. This is also a 1943 k98. |
| If you look at the top view of the bolt of a G33/40 you will not see any serial numbers on it like was shown on the top of a K98 bolt assembly. You will notice that you can see the test fire proof marking on the top of the bolt handle. |
| That is because the serial number is located on the aft side of the bolt turn down handle as shown here. |
| Business end of the G33/40 shows us more differences from the K98. The cleaning rod is shorter. The sight hood cover is also smaller. Also you will notice that the barrel is the same diameter throughout, unlike the K98 which has a wider step for the front sight to mounted to. |
| The floor plate and trigger guard assemble, are both milled types, and are very similar to that of the K98. However, notice that the G33/40 will not have any locking screws like the K98 (exception being the Kriegsmodell K98). Notice also, the hollowed out bolt knob. |
| Of couse the G33/40 will be marked as such in the same location on the reciever as the K98 is. |
| Also the rear sight on the G33/40 is much smaller, and is marked in different graduations. |
| Even the barrel bands are different on a G33/40! The front barrel band appears to be the same as on an early K98, but you will notice that the band spring is mounted on the left side, and not on the right side as on a K98! The rear band is totally different, and has a retaining screw at the bottom of the band. |
| Of course the G33/40 will be marked as such in the same location on the receiver as the K98 is. |
Mauser 98 Serial Number Location
Top of Page